Christie LX750 Uživatelský manuál

LX750/LW650/LS+70064&3."/6"-5&$)/*$"-(6*%&020-0001-01

8RS-232C CommunicationRS-232C Communication678912345 678912345 CONTROL port RS-232C cable (Cross) RS-232C port of the projector of the

9RS-232C Communication (continued)Requesting projector status (Get command)(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes

10Command Control via the NetworkCommunication PortThe following two ports are assigned for the command control.TCP #23TCP #9715Command Control Settin

11Command Control via the Network (continued)Command Format[TCP #23]1. ProtocolConsist of header (7 bytes) + command data (6 bytes)2. HeaderBE + EF +

12Command Control via the Network (continued)Decreasing the projector setting value (Decrement command)(1) The PC sends the following decrement code t

137. Reply DataThe connection ID (the data is same as the connection ID data on the sending data format) is attached to the Network control commands r

14Daisy Chain Communication1.Communications settingSet the same communication settings (selecting from options below) on the CONTROL terminal for tran

15Daisy Chain CommunicationCalculation of Checksum Sum up all of 12 bytes except the Checksum, then make the bit inversion of the lowest byte of the t

16Daisy Chain CommunicationCommand data ①Control the projectorbyte_0 byte_1 byte_2 byte_3 byte_4 byte_5Action Type Setting Codelow high low high low h

17Daisy Chain CommunicationCommand data Requesting projector status (Get command)(1) Send the following request code from the PC to the projector.Head

18Daisy Chain CommunicationGet the number of connected projectors (1) Send the following request code from the PC to the projector.Header + Command da

19Daisy Chain CommunicationGet the communication Group identification and Communication ID (1) Send the following request code from the PC to the proje

20LIT MAN USR LW650/LS+700/LX750 TECH GUID 020-000161-01 Rev.1 (02/09)RS-232C Communication / Network command tableNames Operation Type HeaderCommand

21RS-232C Communication / Network command tableNames Operation Type HeaderCommand DataCRC Action Type Setting CodeGAMMA Set 5 CUSTOM BE EF 03 06 00 C7

22Names Operation Type HeaderCommand DataCRC Action Type Setting CodeRS-232C Communication / Network command tableCOLOR TEMP GAIN R Get BE EF 03 06 00

23RS-232C Communication / Network command tableNames Operation Type HeaderCommand DataCRC Action Type Setting Code3D-YCS Set OFF BE EF 03 06 00 E6 70

24RS-232C Communication / Network command tableNames Operation Type HeaderCommand DataCRC Action Type Setting CodeS-VIDEO FORMAT Set AUTO BE EF 03 06

25RS-232C Communication / Network command tableNames Operation Type HeaderCommand DataCRC Action Type Setting CodeFRAME LOCK - COMPUTER IN 1Set OFF BE

26Names Operation Type HeaderCommand DataCRC Action Type Setting CodeRS-232C Communication / Network command tableMONITOR OUT - HDMISet COMPUTER IN 1

27RS-232C Communication / Network command tableNames Operation Type HeaderCommand DataCRC Action Type Setting CodeLANGUAGE Set POLSKI BE EF 03 06 00 9

1ProjectorL;50/:LS+70User Manual – Technical Guide Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode720 x 400 37.9 85.

28RS-232C Communication / Network command tableNames Operation Type HeaderCommand DataCRC Action Type Setting CodeCLOSED CAPTION CHANNELSet 1 BE EF 03

29RS-232C Communication / Network command tableNames Operation Type HeaderCommand DataCRC Action Type Setting CodeMY BUTTON-1 Set COMPUTER IN 1 BE EF

30RS-232C Communication / Network command tableNames Operation Type HeaderCommand DataCRC Action Type Setting CodeMY BUTTON-3 Set DVI-D BE EF 03 06 00

31RS-232C Communication / Network command tableNames Operation Type HeaderCommand DataCRC Action Type Setting CodeMY SOURCE Get BE EF 03 06 00 C9 38 0

32Names Operation Type HeaderCommand DataCRC Action Type Setting CodeRS-232C Communication / Network command tableLENS MEMORY INDEX Set 1 BE EF 03 06

2Initial set signalsInitial set signalsThe following signals are used for the initial settings. The signal timing of some computer models may be diffe

3Connection to the portsACOMPUTER IN1, BCOMPUTER IN2, CMONITOR OUT D-sub 15pin mini shrink jack• Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω term

4I OHDMI DVI-DCONTROL IN CONTROL OUTREMOTECONTROLINOUTS-VIDEOCOMPUTER IN2COMPUTER IN1VIDEO 1BNCR/Cr/Pr G/Y B/Cb/Pb H V VIDEO 2YCb/PbCr/PrAC INLANMO

5I OHDMI DVI-DCONTROL IN CONTROL OUTREMOTECONTROLINOUTS-VIDEOCOMPUTER IN2COMPUTER IN1VIDEO 1BNCR/Cr/Pr G/Y B/Cb/Pb H V VIDEO 2YCb/PbCr/PrAC INLANMO

6PJLink commandPJLink commandCommands Control Description Parameter or ResponsePOWR Power Contorol0 = Standby1 = Power OnPOWR ? Power Status inquiry0

7PJLink command (continued)Commands Control Description Parameter or ResponseLAMP ? Lamp Status inquiry1st number (digits 1 to 5): Lamp Time2nd number