Christie LX900 Uživatelský manuál Strana 33
- Strana / 90
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Command with Address Specification
LX900 RS232 Codes-Expanded Technical Reference Information 8-7
020-000034-01 Rev 1. (03/08)
8.4.16 CF_IMAGEADJ Command
Command “CF_IMAGEADJ_%1”[CR]
%1 “RST”- Reset adjusted value for the Image
“STR1”- Store current adjusted value to Image 1
“STR2”- Store current adjusted value to Image 2
“STR3”- Store current adjusted value to Image 3
“STR4”- Store current adjusted value to Image 4
“STR5”- Store current adjusted value to Image 5
“STR6”- Store current adjusted value to Image 6
“STR7”- Store current adjusted value to Image 7
“STR8”- Store current adjusted value to Image 8
“STR9”- Store current adjusted value to Image 9
“STR10”- Store current adjusted value to Image 10
Detail Reset or Store adjusted value for Image. (Available only in the normal
Power ON status)
“STR1”-”STR10” corresponds to “Image1”-”Image10” displayed in
projector OSD menu on selecting “Store” for adjusted value of Image.
The setting value set in “Image1” to “Image10” is stored and can be
retrieved when turning on the projector again after the power is turned to
ALL OFF status.
Acceptable “000” [CR] Response
Unacceptable “Error Code” [CR]
8.5 PC Control Command
8.5.1 CF_FSYNC Command
Command “CF_FSYNC_%1” [CR]
%1
“0000-0031” - Directly specify setting value of Fine Sync “UP” - Increment
setting value of Fine Sync by 1 “DN” - Decrement setting value of Fine Sync
by 1
Detail
Set value of Fine Sync in PC signal (Available only in the normal Power ON
status)
The value set by this command is not stored in the projector’s memory.
Therefore, when the power is turned to ALL OFF status, the value returns
to the original setting. (It is stored in Suspend mode.)
Acceptable “000” [CR]
Response
Unacceptable
“101” [CR] - When input is Video signal - When input is no
signal
- LX900 RS232 Codes-Expanded 1
- Table of Contents 3
- Table of Contents 5
- 1 Overview 9
- 2.1 Transfer Specification 11
- 2.2 Connection 11
- 3 Notes for communication 13
- 4 Notation 15
- 5.1 Image Commands Table 17
- 5.4 Screen Command Table 18
- 5.5 Lamp Command Table 18
- 5.7 Other Command Table 19
- 5.6 Setting Command Table 19
- 6 Status Read Command Table 21
- 7 Error Codes Table 25
- 8.1 Format 27
- 8.2 Transfer Example 27
- 8.3 Operation Requirements 27
- 8.4 Image Command 28
- 8.4.4 CF_TINT Command 29
- 8.4.5 CF_COLMNAV Command 29
- 8.4.6 CF_COLMNLD Command 29
- 8.4.7 CF_APCTRL Command 29
- 8.4.8 CF_COLTEMP Command 30
- 8.4.9 CF_WBAL- Command 30
- 8.4.10 CF_OFFSET- Command 30
- 8.4.11 CF_SHARP Command 31
- 8.4.12 CF_GAMMA Command 31
- 8.4.13 CF_NZRED Command 31
- 8.4.14 CF_PROGV Command 32
- 8.4.15 CF_IMAGE Command 32
- 8.5 PC Control Command 33
- 8.5.2 CF_TDOTS Command 34
- 8.5.3 CF_H-POS Command 34
- 8.5.4 CF_V-POS Command 34
- 8.5.5 CF_CLAMP Command 35
- 8.5.6 CF_DDOTS Command 35
- 8.5.7 CF_DLINE Command 35
- 8.5.8 CF_SETPCADJ Command 36
- 8.5.9 CF_ORGMODE Command 36
- 8.5.10 CF_PCSTORE Command 37
- 8.6 Input Control Command 38
- 8.6.3 CF_INPUT1~4 Command 39
- 8.6.4 CF_SYSTEM Command 40
- 8.7 Screen Control Command 42
- 8.7.2 CF_DZCENT Command 43
- 8.7.3 CF_KEYSTONE Command 43
- 8.7.5 CF_CEIL Command 44
- 8.7.6 CF_REAR Command 44
- 8.7.7 CF_VSCALE Command 44
- 8.7.8 CF_VPOS Command 45
- 8.7.9 CF_HSCALE Command 45
- 8.8 Lamp Commands 46
- 8.9 Setting Command 47
- 8.9.2 CF_DISP Command 48
- 8.9.3 CF_BACKGND Command 48
- 8.9.4 CF_LOGO Command 49
- 8.9.5 CF_FANSPEED Command 49
- 8.9.6 CF_RCODE Command 50
- 8.9.7 CF_RSENS Command 50
- 8.9.8 CF_P-MANE Command 51
- 8.9.9 CF_P-MANETIME Command 51
- 8.9.10 CF_ON-STA Command 51
- 8.9.11 CF_PJPINCODE Command 52
- 8.9.12 CF_FILH Command 52
- 8.9.13 CF_FILTIMER Command 52
- 8.9.14 CF_FILCTL Command 53
- 8.9.15 CF_FILSCRL Command 53
- 8.9.16 CF_TESTPAT Command 53
- 8.9.18 CF_KEYDIS Command 54
- 8.9.21 CF_SHUTH Command 54
- 8.10 Other Command 55
- 9 Status Read Commands 57
- 9.4.3 CR_COLOR Command 58
- 9.4.4 CR_TINT Command 58
- 9.4.5 CR_APCTRL Command 58
- 9.4.6 CR_COLTEMP Command 58
- 9.4.7 CR_WBAL-R Command 59
- 9.4.8 CR_WBAL-G Command 59
- 9.4.9 CR_WBAL-B Command 59
- 9.4.10 CR_OFFSET-R Command 59
- 9.4.11 CR_OFFSET-G Command 59
- 9.4.12 CR_OFFSET-B Command 60
- 9.4.13 CR_SHARP Command 60
- 9.4.14 CR_GAMMA Command 60
- 9.4.15 CR_NZRED Command 60
- 9.4.16 CR_PROGV Command 61
- 9.4.17 CR_IMAGE Command 61
- 9.5 PC Status Read Commands 62
- 9.5.4 CR_V-POS Command 63
- 9.5.5 CR_CLAMP Command 63
- 9.5.6 CR_DDOTS Command 63
- 9.5.7 CR_DLINE Command 63
- 9.5.8 CR_SETPCADJ Command 64
- 9.5.9 CR_ORGMODE Command 65
- 9.7 Input Read Command 66
- 9.7.2 CR_SOURCE Command 67
- 9.7.3 CR_SYSTEM Command 68
- 9.7.4 CR_SRCINP1 Command 69
- 9.7.6 CR_SRCINP3 Command 70
- 9.7.7 CR_SRCINP4 Command 70
- 9.7.8 CR_HMSLOT Command 70
- 9.7.5 CR_SRCINP2 Command 70
- 9.7.9 CR_NMSLOT1 Command 71
- 9.7.10 CR_NMSLOT2 Command 71
- 9.7.11 CR_NMSLOT3 Command 71
- 9.7.12 CR_NMSLOT4 Command 71
- 9.7.13 CR_IDSLOT1 Command 72
- 9.7.14 CR_IDSLOT2 Command 72
- 9.7.15 CR_IDSLOT3 Command 72
- 9.7.16 CR_IDSLOT4 Command 73
- 9.8.1 CR_SCREEN Command 73
- 9.8.2 CR_KYSTNMODE Command 73
- 9.8.3 CR_CEIL Command 73
- 9.8.4 CR_REAR Command 74
- 9.8.5 CR_VSCALE Command 74
- 9.8.6 CR_VPOS Command 74
- 9.8.7 CR_HSCALE Command 74
- 9.8.8 CR_HPOS Command 75
- 9.9.1 CR_LAMPREPL Command 75
- 9.9.2 CR_LAMPMODE Command 75
- 9.9.4 CR_LAMPSTS Command 76
- 9.9.5 CR_INFLAMP Command 76
- 9.9.6 CR_PROJH Command 76
- 9.9.7 CR_HMLAMP Command 76
- 9.9.8 CR_LAMPH Command 77
- 9.10.1 CR_BACKGND Command 77
- 9.10.2 CR_DISP Command 77
- 9.10.3 CR_LOGO Command 78
- 9.10.4 CR_LOGOLOCK Command 78
- 9.10.5 CR_RCODE Command 78
- 9.10.6 CR_RSENS Command 78
- 9.10.7 CR_LANG Command 79
- 9.10.8 CR_ON-STA Command 79
- 9.10.9 CR_P-MANE Command 79
- 9.10.11 CR_FANSPEED Command 80
- 9.10.12 CR_KEYDIS Command 80
- 9.10.15 CR_SHUTH Command 81
- 9.10.16 CR_SECURITY Command 81
- 9.10.19 CR_FILH Command 82
- 9.10.20 CR_FILCOND Command 82
- 9.10.21 CR_FILREPL Command 82
- 9.10.22 CR_FILTIMER Command 82
- 9.10.24 CR_TESTPAT Command 83
- 9.11.1 CR_STATUS Command 84
- 9.11.2 CR_SIGNAL Command 84
- 9.11.3 CR_VMUTE Command 85
- 9.11.4 CR_FREEZE Command 85
- 9.11.5 CR_P-TIMER Command 85
- 9.11.6 CR_TEMPWARN Command 86
- 9.11.7 CR_TEMPFAIL Command 87
- 9.11.8 CR_SERIALNO Command 87
- 10.1 Overview 89
- 10.3.1 Format 90
Související produkty a manuály pro Projektory Christie LX900
Projektory Christie L2K1500 Uživatelský manuál
(36 stránky)
(36 stránky)
Projektory Christie DHD800 Uživatelský manuál
(97 stránky)
(97 stránky)
Projektory Christie LW600 Uživatelský manuál
(101 stránky)
(101 stránky)
Projektory Christie 38-VIV205-01 Uživatelský manuál
(44 stránky)
(44 stránky)
Projektory Christie LS+700 Uživatelský manuál
(54 stránky)
(54 stránky)
Projektory Christie LX750 Uživatelský manuál
(28 stránky)
(28 stránky)
Projektory Christie DWX951 Uživatelský manuál
(111 stránky)
(111 stránky)
Projektory Christie CP2000-X Průvodce nastavením
(64 stránky)
(64 stránky)
Projektory Christie Christie HDDW Instalační manuál
(100 stránky)
(100 stránky)
Projektory Christie Christie HDDW Uživatelský manuál
(62 stránky)
(62 stránky)
(28 stránky)
Projektory Christie LCD projector Uživatelský manuál
(140 stránky)
(140 stránky)
Projektory Christie LW600 Uživatelský manuál
(32 stránky)
(32 stránky)
Projektory Christie DHD600-G Manuál s instrukcemi
(73 stránky)
(73 stránky)
Projektory Christie Entero RPMWU Průvodce nastavením
(58 stránky)
(58 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce